Melamine Foam Processing & Installation Boundaries

Engineering Applications, Processing & Installation Responsibility Boundaries

Kangerna supplies engineered melamine foam components through seven fabrication routes. We make to the approved drawing, sample and contract specification; installation on site is led by the customer or its appointed contractor.

7 fabrication routes Drawing or sample approval Clear handover point
7
Fabrication routes
2500 × 1250 mm
Largest listed working envelope
2 references
Approved drawing or sample
1 clear boundary
Customer-led site installation
Fabrication scope

From foam material to a defined component

Each project starts with a defined process and an agreed production reference. Review the route that matches your component, then confirm the material, geometry and commercial details before bulk production.

01 / MAKE

We manufacture the component

We process melamine foam into the agreed shape, composite or finished component using one or more of the listed routes.

02 / CONFIRM

We align to the approved reference

The approved drawing or sample, together with the agreed material, dimensions and contract, becomes the production baseline.

03 / HAND OVER

Installation remains with you

The component is supplied for installation by the customer or its appointed contractor. Site conditions and installation decisions remain outside our scope.

01

CNC shaping & engraving

CNC processing product page

CNC cutting, engraving and special-shape processing of melamine foam components.

What to specify: a drawing is optional for initial review; final geometry, dimensions and material are confirmed by the approved drawing or sample.

Working limit2500 × 1250 mm
InstallationCustomer / appointed contractor
Bulk consistencyBulk production follows the approved sample, drawing and contract.
02

Double-sided adhesive backing

Self-adhesive foam product page

Melamine foam supplied with a double-sided adhesive backing for downstream assembly.

What to specify: the adhesive requirement, component dimensions and any liner or application details relevant to your process.

Working limit2500 × 1200 mm
InstallationCustomer / appointed contractor
Bulk consistencyBulk production follows the approved sample, drawing and contract.
03

Aluminum foil lamination

Aluminum foil foam product page

Hot-melt aluminum foil lamination applied to melamine foam components.

What to specify: the required aluminum foil specification, dimensions and the application conditions the component must suit.

Working limit2500 × 1200 mm
InstallationCustomer / appointed contractor
Bulk consistencyBulk production follows the approved sample, drawing and contract.
04

Pipe insulation components

Pipe insulation product page

Melamine foam pipe insulation sections and related shaped components.

What to specify: foam color, jacket outside and inside diameters, and the required component length.

Working limitMaximum outside diameter 400 mm
InstallationCustomer / appointed contractor
Bulk consistencyBulk production follows the approved sample, drawing and contract.
05

Fabric or leather wrapped acoustic panels

Wrapped acoustic panel product page

Melamine foam acoustic panels finished with fabric or leather wrapping.

What to specify: the panel shape, final dimensions and the fabric or leather requirement for approval.

Working limit2500 × 1250 mm
InstallationCustomer / appointed contractor
Bulk consistencyBulk production follows the approved sample, drawing and contract.
06

Melamine foam combined with scouring pad material for floor-pad applications.

What to specify: final dimensions, scouring-pad material and color, plus the required foam build.

Working limitMaximum diameter 700 mm
InstallationCustomer / appointed contractor
Bulk consistencyBulk production follows the approved sample, drawing and contract.
07

Mop heads made from foam with raised fabric, or a foam, PU and raised-fabric composite.

What to specify: final size, color and material construction, including the raised-fabric and PU requirements where applicable.

Working limit500 × 500 × 40 mm
InstallationCustomer / appointed contractor
Bulk consistencyBulk production follows the approved sample, drawing and contract.
Approval workflow

One reference controls the build

Clear approval before production reduces ambiguity between a concept, a sample and a bulk order. The process below applies to the seven fabrication routes on this page.

Production rule The approved drawing and/or approved sample, together with the agreed material and dimensions, is the reference for bulk production.
01

Share the requirement

Send the process, intended application, dimensions, quantity and any drawing or sample available for review.

02

Review the reference

We review the requested material, process, geometry and any tooling or composite details relevant to feasibility.

03

Approve the specification

Material, color, dimensions, construction, quantity and commercial details are confirmed in the quotation and approved reference.

04

Produce against the reference

Bulk production is aligned with the approved drawing or sample and the signed contract. Changes should be agreed before the affected batch is produced.

05

Check and hand over

Resolve any consistency question against the approved sample, drawing and contract. Installation is then handled by the customer or appointed contractor.

Responsibility split

Who owns what, from specification to site

A clean handover starts with explicit responsibilities. The supplier scope covers component manufacture and consistency with the approved reference; the customer scope covers project decisions, installation and site conditions.

Supplier scope · Kangerna

Component manufacturing

  • Manufacture to the approved drawing or sample, agreed material, dimensions and process.
  • Use the confirmed specification as the production baseline for the order.
  • Keep bulk production consistent with the approved sample, drawing and contract.
  • Review any requested change before it affects the relevant production batch.
  • Address consistency questions by referring to the approved reference and agreed order terms.
Customer scope · Project team

Application & installation

  • Confirm the product, process, material, dimensions and acceptance requirements.
  • Provide accurate measurements, drawings, samples and written approvals.
  • Assess suitability for the substrate, adjacent materials, operating environment and intended system.
  • Manage transport, storage, handling, fixings, installation and site safety.
  • Meet site-specific regulatory, permit and compliance requirements.
Supplier handoverFinished component aligned to the approved reference
Handover point
Customer scopeOn-site handling, installation, performance in service and site safety
Project brief

What to include before you request a quotation

A complete brief helps us review feasibility, identify the right process and return a more precise quotation. If a detail is not yet fixed, flag it clearly so it can be resolved before approval.

  1. Product or processCNC, adhesive backing, foil lamination, pipe insulation, wrapped panels, floor pads or mop heads.
  2. Geometry & dimensionsLength, width, thickness, diameter, shape and any critical tolerance.
  3. Drawing or sampleProvide the current reference and identify which revision is approved for production.
  4. Material & colorFoam build, color, density or other material requirement already specified by your project.
  5. Composite requirementsAdhesive, aluminum foil, fabric, leather, scouring pad, PU or raised fabric as applicable.
  6. QuantitySample quantity, first order and expected repeat volume, stated separately.
  7. Application contextWhere the component will be used, the adjacent system and relevant operating conditions.
  8. Delivery & documentsDestination, required documentation and any project-specific submission requirements.
FAQ

Questions before you send a drawing

Five practical answers about scope, approval and installation responsibility.

Can you manufacture components from our drawing or sample?

Yes. We review the drawing or sample, confirm material, dimensions and process, and use the approved specification as the production reference.

Which processing routes can you support?

CNC shaping, double-sided adhesive backing, hot-melt aluminum foil lamination, pipe insulation, fabric or leather wrapped acoustic panels, scouring-pad composite floor pads, and composite mop heads.

Who is responsible for installation?

Installation is by the customer or its appointed contractor. We supply the component; handling, substrate preparation, fixings, installation and site safety remain the customer’s scope.

What if bulk production differs from the approved sample or drawing?

Contact us with the order number, batch information, photos and affected quantity. We review the issue against the approved sample, drawing and contract before agreeing corrective action.

What information should we provide before quotation?

Product or process, dimensions, drawing or sample, material and color, adhesive/foil/fabric requirements, quantity, application, destination and any required documents.

Next step

Discuss your drawing or project requirements

Send the component details, application context, quantity and available drawing or sample. Our team will review the appropriate process and the information needed for quotation.

Contact Kangerna
Dejar un mensaje
Nombre
Correo electrónico *
Mensaje
Utilizamos Galleta Para mejorar su experiencia en línea. Al continuar navegando por este sitio web, asumimos que acepta nuestro uso de Galleta .
Message Us